產品概述
BLD -- 電子萬能拉力試驗機 （液晶顯示）
一、拉力試驗機是用來對材料進行靜載、拉伸、壓縮、彎曲、剪切、剝離等力學性能試驗用的機械加力的試驗機，適用于塑料板材、管材、異型材，塑料薄膜及橡膠、電線電纜等材料的各種物理機械性能測試為材料開發，為物性試驗、教學研究、質量控制等*的檢測設備，拉力機夾具作為儀器的重要組成部分，不同的材料需要不同的夾具，也是試驗能否順利進行及試驗結果準確度高低的一個重要因素。
二、適用范圍：
BLD系列 液晶顯示電子萬能試驗機滿足GB1040， GB13022，GB17200，GB16491等要求。主要適用于金屬及非金屬材料的測試，如橡膠、塑料、電線電纜、光纖光纜、安全帶、保險帶、皮革皮帶復合材料、塑料型材、防水卷材、鋼管、銅材、型材、彈簧鋼、軸承鋼、不銹鋼（以及其它高硬度鋼）、鑄件、鋼板、鋼帶、有色金屬金屬線材的拉伸、壓縮、彎曲、剪切、剝離、撕裂、兩點延伸（需另配引伸計）等多種試驗. 廣泛應用于計量質檢；橡膠塑料；冶金鋼鐵；機械制造；電子電器；汽車生產；紡織化纖；電線電纜；包裝材料和食品；儀器儀表；科研器械；民用核能；高等院校；科研實驗所；商檢仲裁、技術監督部門；建材陶瓷；石油化工；其它行業。
三、主要特點
采用進口光電編碼器進行位移測量，控制器采用嵌入式單片微機結構，內置功能強大的測控軟件，集測量、控制、計算、存儲功能于一體。具有自動計算應力、延伸率（需加配引伸計）、抗拉強度、彈性模量的功能，自動統計結果；自動記錄zui大點、斷裂點、點的力值或伸長量；采用計算機進行試驗過程及試驗曲線的動態顯示，并進行數據處理，試驗結束后可通過圖形處理模塊對曲線放大進行數據再分析編輯，并可打印報表，產品性能達到先進水平。
四、主要技術指標：
01、zui大試驗力:單柱結構：0-5KN（試驗力大小可根據用戶需求而定）
02、試驗力顯示范圍:0～5KN
03、試驗力分檔：全程不分檔-*/
04、試驗力測量精度:優于示值的±1%
05、位移分辨率:0.01mm
06、位移測量準確度:優于示值的±1%
07、橫梁移動速度控制范圍:0.05mm/min～300mm/min
08、位移速度控制精度:優于±1%
09、拉伸行程:0～800mm（不含夾具）
10、外形尺寸（長×寬×高）: 435mm×275mm×1700mm（單柱）
11、供電電源:220V、50Hz
五、配置：
01、高強度主機一臺（單臂式結構）
02、高精度光電編碼器一支
03、全數字調速系統和全數字調速電機各一套
04、精密絲杠副一套
05、精密圓弧同步減速系統一套
06、高精度傳感器一支
07、拉伸輔具一套
08、萬能試驗機控制系統及大液晶顯示器一套
六、功能介紹：
01、速度瞬間切換：試驗過程中可按預先設定的三個速度瞬間切換，以節約試驗時間
02、自動停機：試樣破壞后，移動橫梁自動停止移動
03、顯示方式：試驗過程動態實時顯示試驗力、位移量、試驗速度、峰值、試驗狀態同時實時在同一液晶屏幕上顯示
04、自動返回：試驗完成后試驗機移動橫梁自動返回到試驗初始位置
05、限位保護：具有程控和機械兩級限位保護功能
06、過載保護：當負荷超過額定值的3～5%時設備自動停止工作
07、自動打印：配制微型打印機，可對測試的數據進行打印
北京北廣精儀儀器有限公司是從事專業測量儀器以及相關設備的研發、生產、銷售、于一體是股份企業，并按照現代化經營管理實現企業化經營管理模式走向股份制正規化企業，公司經過長期發展，現已擁有獨立的研發隊伍并已有海內外專家入注進行產品的研發與設計。
七、故障及解決方法：
一、拉力試驗機加荷時，指針顫動或時走時停
1、離合器齒輪磨損：需要修理或更換。
2、摩擦盤的皮墊圈或彈簧磨損：需更換皮墊圈或彈簧。
3、操縱手柄移位：調整操縱手柄，使其與牙槽配合好。
二、更換擺砣時指針不回零
1、拉力試驗機安裝不水平：用水平儀把試驗機調整水平。
2、擺錘不垂直：只掛A砣。調整平衡砣，使之垂直。
三、拉力試驗機擺錘回位太快或太慢
1、緩沖閥擋位位置放置不當：調整緩沖閥到適當位置。
2、液壓油黏度過低或過高：液壓油黏度過低時擺錘回落快，黏度高時回落慢．應更換適當黏度的液壓油。
3、緩沖閥內、油管內或液壓油有臟污：清洗緩沖閥、油管。更換液壓油。
四、拉力試驗機指針回零滯怠或不穩定
1、指針軸承、主軸軸承銹蝕或有油污：清洗或更換軸承。
2、齒桿變形或齒桿與齒輪不嚙合：校直齒桿或清洗、修整齒輪、槽輪等傳動部件。
3、緩沖閥內有臟污：清洗緩沖閥。
五、拉力試驗機示值正偏差
1、短臂刀刃有松動：把刀刃緊牢。
2、擺砣偏輕：給砣配重（要兼顧A、B、C砣的重量）。
六、示值負偏差zui主要原因是各部件之間的摩擦阻力過大
1、指針軸承、擺軸軸承和測力傳動部件摩擦阻力過大：主要是調整、清洗軸承及測力傳動部件．消除不正常的摩擦阻力。
2、上夾頭、從動針彈簧片松緊度和描繪裝置的摩擦阻力大：調整上夾頭、從動針彈簧片松緊度和描繪裝置部件．消除不正常的摩擦阻力。
3、活塞桿與擺桿相接部位不靈活：調整兩者相接部位。使之靈活自如。
七、從動針滯阻或移位
1、從動針彈簧片彈力大小或從動針與指示盤摩擦阻力大小造成的影響：調整從動針彈簧片的彈力或從動針與指示盤的問隙。
2、從動針兩端重鼉有偏差：調整兩端重量，使其平衡。
八、示值無規律的偏差
1、齒桿、齒輪有油污、磨損或有毛刺：消除齒桿、齒輪的油污、毛刺，找出超差時的齒桿接觸點，然后修正齒桿、齒輪；如不能消除誤差．更換齒桿、齒輪。
2、拉力試驗機試驗機安裝不水平：調整水平。
3、齒桿彎曲：校直或更換齒桿，調整滾動槽輪的問隙。
九、計算機軟件聯機后出現提示框信息顯示超載。
解決方案是檢查計算機與試驗機的通訊線是否脫落;檢查聯機選擇傳感器是否選擇正確;檢查zui近的試驗或操作鍵
盤時傳感器是否被撞過;檢查出現問題之前是否使用了軟件的校準或標定功能;檢查是否手動更改過校準值、標定值或硬件參數中的其他信息。
十、試驗機主機電源不亮，不能上下移動。
解決方案是檢查接入試驗機的電源線路是否連接正常;檢查急停開關是否處于擰起狀態;檢查接入試驗機的電源電壓是否正常;檢查機器插座上的保險是否燒斷，請取出備用保險絲安裝即可。
十一、試驗機主機電源有電但設備不可以上下移動。
解決方案是檢查是否是15S（時間）以后設備還無法移動，因為主機開機需要自檢，大概需要15S時間;檢查上下限位是否再恰當的位置，有一定的運行空間;檢查接入試驗機的電源電壓是否正常。
八、油源的保養：
1、定期檢查主機和油源處是否有漏油的地方，如發現有漏油，應及時更換密封圈或組合墊;
2、根據機器的使用情況及油的使用期限，定期更換吸油過濾器和濾芯，更換液壓油。
3、長時間不做試驗時，注意關斷主機電源。如果機器在待機狀態，轉換開關應打到“加載”檔，因為如果轉換開關打在“快退”檔，電磁換向閥一直在通電狀態，會影響 該器件的使用壽命。
九、控制系統保養：
1、定期檢查控制器后面板的連接線是否接觸良好，如有松動，應及時緊固;
2、試驗后若有一段較長的時間不用機器時，關閉控制器和電腦;
3、控制器上的接口為一一對應，插錯接口可能對設備造成損壞;
4、插拔控制器上的接口必須關閉控制器電源。
BLD - electronic universal tensile testing machine （liquid crystal display）
一、拉力試驗機是用來對材料進行靜載、拉伸、壓縮、彎曲、剪切、剝離等力學性能試驗用的機械加力的試驗機，適用于塑料板材、管材、異型材，塑料薄膜及橡膠、電線電纜等材料的各種物理機械性能測試為材料開發，為物性試驗、教學研究、質量控制等*的檢測設備，拉力機夾具作為儀器的重要組成部分，不同的材料需要不同的夾具，也是試驗能否順利進行及試驗結果準確度高低的一個重要因素。
A testing machine, tensile testing machine is used for mechanical loading static load, tensile, compression, bending, shear, stripping and other mechanical properties test of the material, suitable for plastic sheet, pipe, profile, all kinds of plastic film and rubber, wire and cable materials such as the physical and mechanical performance test for the material development, as the indispensable testing equipment character test, teaching and research, quality control, tensile machine fixture as an important part of the instrument, different materials have different fixtures, and test can be an important factor in smoothly and test the accuracy of height.
二、適用范圍：
Two, applicable scope:
BLD系列 液晶顯示電子萬能試驗機滿足GB1040， GB13022，GB17200，GB16491等要求。主要適用于金屬及非金屬材料的測試，如橡膠、塑料、電線電纜、光纖光纜、安全帶、保險帶、皮革皮帶復合材料、塑料型材、防水卷材、鋼管、銅材、型材、彈簧鋼、軸承鋼、不銹鋼（以及其它高硬度鋼）、鑄件、鋼板、鋼帶、有色金屬金屬線材的拉伸、壓縮、彎曲、剪切、剝離、撕裂、兩點延伸（需另配引伸計）等多種試驗. 廣泛應用于計量質檢；橡膠塑料；冶金鋼鐵；機械制造；電子電器；汽車生產；紡織化纖；電線電纜；包裝材料和食品；儀器儀表；科研器械；民用核能；高等院校；科研實驗所；商檢仲裁、技術監督部門；建材陶瓷；石油化工；其它行業。
BLD series liquid crystal display electronic universal testing machine to meet the GB1040, GB13022, GB17200, GB16491 etc.. Mainly used in metal and non-metallic materials testing, such as rubber, plastic, wire and cable, fiber optic cable, safety belt, safety belt, leather belt, plastic composite materials, waterproofing materials, steel, copper, profiles, spring steel, bearing steel, stainless steel （and its high hardness steel）, casting, steel plate, steel, non-ferrous metal wire tensile, compression, bending, shear, peel, tear, two extension （other extensometer） and other tests. Widely used in measurement and quality inspection; rubber; iron and steel metallurgy; machinery manufacturing; electrical and electronic; auto manufacturing; textile; cable; packaging material and food; instruments; medical equipment; civil nuclear energy; University; Research Institute; arbitration, technical supervision departments; building ceramics; petrochemical industry.
三、主要特點
Three, the main features
采用進口光電編碼器進行位移測量，控制器采用嵌入式單片微機結構，內置功能強大的測控軟件，集測量、控制、計算、存儲功能于一體。具有自動計算應力、延伸率（需加配引伸計）、抗拉強度、彈性模量的功能，自動統計結果；自動記錄zui大點、斷裂點、點的力值或伸長量；采用計算機進行試驗過程及試驗曲線的動態顯示，并進行數據處理，試驗結束后可通過圖形處理模塊對曲線放大進行數據再分析編輯，并可打印報表，產品性能達到先進水平。
Imported photoelectric encoder displacement measurement, controller adopts the embedded single chip microcomputer structure, measurement and control software with powerful, measurement, control, calculation, storage functions. With automatic calculation of stress, elongation （required with extensometer）, tensile strength, modulus of elasticity function, automatic statistics; automatically records the maximum point, the breaking point, the designated point force value or elongation; dynamic uses the computer to carry on the test process and test curve display, and data processing, the end of the test after the amplification curve of the reanalysis data edit graphics processing module, and print statements, product performance has reached the international advanced level.
四、主要技術指標：
Four, the main technical indicators:
01、zui大試驗力:單柱結構：0-5KN（試驗力大小可根據用戶需求而定）
01, the maximum test force: single column structure: 0-5KN （testing force can be based on user demand）
02、試驗力顯示范圍:0～5KN
02, the test force display range: 0 ~ 5KN
03、試驗力分檔：全程不分檔-*/
03, test sub-file: full unclassified -*/
04、試驗力測量精度:優于示值的±1%
04, the test force measuring accuracy: better than showing the value of ± 1%
05、位移分辨率:0.01mm
05, the displacement resolution: 0.01mm
06、位移測量準確度:優于示值的±1%
06, the displacement measurement accuracy: better than showing the value of ± 1%
07、橫梁移動速度控制范圍:0.05mm/min～300mm/min
07, beam speed control range: 0.05mm/min ~ 300mm/min
08、位移速度控制精度:優于±1%
The accuracy of 08, displacement and speed control: better than ± 1%
09、拉伸行程:0～800mm（不含夾具）
09, stretching stroke: 0 ~ 800mm （excluding fixture）
10、外形尺寸（長×寬×高）: 435mm×275mm×1700mm（單柱）
10, size （length * width * height）: 435mm * 275mm * 1700mm （single column）
11、供電電源:220V、50Hz
11, power supply: 220V, 50Hz
五、配置：
Five, configuration:
01、高強度主機一臺（單臂式結構）
01, high strength and a host （single-arm type structure）
02、高精度光電編碼器一支
02, a high precision photoelectric encoder
03、全數字調速系統和全數字調速電機各一套
03, a full digital control system and the full digital speed regulating motor a
04、精密絲杠副一套
04, a set of precision screw
05、精密圓弧同步減速系統一套
05, precise arc synchronous reduction system
06、高精度傳感器一支
06, a high precision sensor
07、拉伸輔具一套
07, a set of special stretching device
08、萬能試驗機控制系統及大液晶顯示器一套
08, universal testing machine control system and large liquid crystal display a set of
六、功能介紹：
Six, function introduction:
01、速度瞬間切換：試驗過程中可按預先設定的三個速度瞬間切換，以節約試驗時間
01, speed instantly switch: test process according to the preset three speed instantly switch, to save the test time
02、自動停機：試樣破壞后，移動橫梁自動停止移動
02, automatic shutdown: sample destruction, automatic stop moving.
03、顯示方式：試驗過程動態實時顯示試驗力、位移量、試驗速度、峰值、試驗狀態同時實時在同一液晶屏幕上顯示
03, display mode: test process dynamic real-time display test force, displacement, test speed, peak, test at the same time in the same LCD screen display
04、自動返回：試驗完成后試驗機移動橫梁自動返回到試驗初始位置
04, automatic return: after completion of the test test machine moving beam automatically return to the initial position
05、限位保護：具有程控和機械兩級限位保護功能
05, limit protection: a programmable and machinery two limit protection function
06、過載保護：當負荷超過額定值的3～5%時設備自動停止工作
06, overload protection: when the load exceeds the rated value 3 ~ 5% when the equipment stops working automatically
07、自動打印：配制微型打印機，可對測試的數據進行打印
07, automatic printing: the preparation of micro printer, print the test data
Beijing Beiguang Precision Instrument Co. Ltd. is a professional R & D, measuring instruments and related equipment, production, sales in one high-tech shares in enterprises, and in accordance with the implementation of modern management of the enterprise management mode to the joint-stock enterprise standardization, the company after a long-term development, and now owns independent R & D team and has been at home and abroad expert injection for product development and design.
七、故障及解決方法：
Seven, fault and solution method:
一、拉力試驗機加荷時，指針顫動或時走時停
A, tensile test machine, vibration or pause the pointer
1、離合器齒輪磨損：需要修理或更換。
1, the clutch gear wear: the need for repair or replacement.
2、摩擦盤的皮墊圈或彈簧磨損：需更換皮墊圈或彈簧。
2, the skin friction disc washer or spring wear: need to change the skin or spring washer.
3、操縱手柄移位：調整操縱手柄，使其與牙槽配合好。
3, handle shift: to adjust the control handle, make it fit in with the alveolar.
二、更換擺砣時指針不回零
Two, the replacement of pendulum weight when the pointer does not return to zero
1、拉力試驗機安裝不水平：用水平儀把試驗機調整水平。
1, tensile testing machine installation is not level: the level to adjust the level of test machine.
2、擺錘不垂直：只掛A砣。調整平衡砣，使之垂直。
2, not only the vertical pendulum hanging weight: A. Adjust the balance weight, so that the vertical.
三、拉力試驗機擺錘回位太快或太慢
Three, tensile testing machine, the pendulum back a bit too fast or too slow
1、緩沖閥擋位位置放置不當：調整緩沖閥到適當位置。
1, the buffer valve gear position placed improper: adjust the buffer valve to the appropriate location.
2、液壓油黏度過低或過高：液壓油黏度過低時擺錘回落快，黏度高時回落慢．應更換適當黏度的液壓油。
2, the hydraulic oil viscosity is too low or too high: hammer down fast swing hydraulic oil viscosity is too low, viscosity is high down slowly. Should be proper replacement of hydraulic oil viscosity.
3、緩沖閥內、油管內或液壓油有臟污：清洗緩沖閥、油管。更換液壓油。
Vittae 3, buffer valve, or hydraulic oil dirty: washing buffer valve, pipe. Replacement of hydraulic oil.
四、拉力試驗機指針回零滯怠或不穩定
Four, tensile testing machine pointer back to zero lag or unstable
1、指針軸承、主軸軸承銹蝕或有油污：清洗或更換軸承。
1, the pointer bearing, spindle bearing corrosion or oil: clean or replace bearing.
2、齒桿變形或齒桿與齒輪不嚙合：校直齒桿或清洗、修整齒輪、槽輪等傳動部件。
2, toothed bar deformation or toothed bar and gear is not engaged: straightening toothed bar or washing, dressing gear, wheel, transmission parts.
3、緩沖閥內有臟污：清洗緩沖閥。
3, the buffer valve with cleaning: cleaning buffer valve.
五、拉力試驗機示值正偏差
Five, tensile testing machine showing the value of positive deviation
1、短臂刀刃有松動：把刀刃緊牢。
1, the short arm loose: the knife blade tightly.
2、擺砣偏輕：給砣配重（要兼顧A、B、C砣的重量）。
2, swing weight lighter: give weight weight （both A, B, C weight weight）.
六、示值負偏差zui主要原因是各部件之間的摩擦阻力過大
Six, showing the value of negative deviation is the main reason of the frictional resistance between the units is too large
1、指針軸承、擺軸軸承和測力傳動部件摩擦阻力過大：主要是調整、清洗軸承及測力傳動部件．消除不正常的摩擦阻力。
1, the pointer shaft bearing, bearing and power transmission parts friction resistance is too large: mainly adjustment, cleaning bearings and force transmission parts to eliminate the friction resistance is not normal.
2、上夾頭、從動針彈簧片松緊度和描繪裝置的摩擦阻力大：調整上夾頭、從動針彈簧片松緊度和描繪裝置部件．消除不正常的摩擦阻力。
Friction resistance on 2, chuck, driven needle leaf spring tightness and describe the adjustment device: chuck, driven needle leaf spring tightness and drawing device components. To eliminate the friction resistance is not normal.
3、活塞桿與擺桿相接部位不靈活：調整兩者相接部位。使之靈活自如。
3, the piston rod and the swing rod is connected with the flexible adjustment of both parts not connected parts. The flexible.
七、從動針滯阻或移位
Seven, the driven needle stagnation or shift
1、從動針彈簧片彈力大小或從動針與指示盤摩擦阻力大小造成的影響：調整從動針彈簧片的彈力或從動針與指示盤的問隙。
Effect of 1, driven needle leaf spring elastic force or driven needle and dial friction resistance caused by the gap adjustment driven needle: the elasticity of the spring piece or driven needle and dial.
2、從動針兩端重鼉有偏差：調整兩端重量，使其平衡。
2, the driven needle are heavy alligator deviation: adjusting the weights, the balance.
八、示值無規律的偏差
Eight, showing the value of deviation is irregular
1、齒桿、齒輪有油污、磨損或有毛刺：消除齒桿、齒輪的油污、毛刺，找出超差時的齒桿接觸點，然后修正齒桿、齒輪；如不能消除誤差．更換齒桿、齒輪。
1, rack, gear oil, abrasion or burr: eliminate the rack, gear oil, burr, find out the pole difference when the contact points, and then modified tooth bar, gear; if not eliminate errors. Replace the tooth bar, gear.
2、拉力試驗機試驗機安裝不水平：調整水平。
2, tensile testing machine testing machine installation is not level: level adjustment.
3、齒桿彎曲：校直或更換齒桿，調整滾動槽輪的問隙。
3, toothed bar bending: alignment or replacement tooth bar, adjust the roll gap groove wheel.
九、計算機軟件聯機后出現提示框信息顯示超載。
Nine, computer software on-line prompt box display information overload.
解決方案是檢查計算機與試驗機的通訊線是否脫落;檢查聯機選擇傳感器是否選擇正確;檢查zui近的試驗或操作鍵
The solution is to check the computer and test machine communication line is off; check the online selection of sensor is correct; check the last test or operation keys
盤時傳感器是否被撞過;檢查出現問題之前是否使用了軟件的校準或標定功能;檢查是否手動更改過校準值、標定值或硬件參數中的其他信息。
When the sensor is knocked off; check whether the use of a software appears calibration or calibration before; check whether the manual modified calibration values, calibration information value or other hardware parameters in the.
十、試驗機主機電源不亮，不能上下移動。
Host ten, the power of the testing machine does not light, not to move up and down.
解決方案是檢查接入試驗機的電源線路是否連接正常;檢查急停開關是否處于擰起狀態;檢查接入試驗機的電源電壓是否正常;檢查機器插座上的保險是否燒斷，請取出備用保險絲安裝即可。
The solution is power line inspection access testing machine is connected properly; check the emergency stop switch is in screwed up state; power supply voltage check access testing machine is normal; check the socket on the insurance is burned off, remove the spare fuse can be installed.
十一、試驗機主機電源有電但設備不可以上下移動。
Host eleven, testing machine power supply with power but the equipment can not move up and down.
解決方案是檢查是否是15S（時間）以后設備還無法移動，因為主機開機需要自檢，大概需要15S時間;檢查上下限位是否再恰當的位置，有一定的運行空間;檢查接入試驗機的電源電壓是否正常。
The solution is to check whether it is 15S （time） after the device is unable to move, because the host boot take self-inspection, probably need 15S time; check the upper and lower limit is again appropriate position, operating space; check supply voltage access testing machine is normal.
八、油源的保養：
Eight, oil source:
1、定期檢查主機和油源處是否有漏油的地方，如發現有漏油，應及時更換密封圈或組合墊;
1, regularly check the host and the supply of oil leaks place, if there is oil leakage, should be promptly replaced seal ring or a combined pad;
2、根據機器的使用情況及油的使用期限，定期更換吸油過濾器和濾芯，更換液壓油。
2, according to the use condition and oil machine use period, replace the oil filter and filter periodically, replacing the hydraulic oil.
3、長時間不做試驗時，注意關斷主機電源。如果機器在待機狀態，轉換開關應打到“加載”檔，因為如果轉換開關打在“快退”檔，電磁換向閥一直在通電狀態，會影響 該器件的使用壽命。
Experiment 3, not long time, pay attention to shut off the main power. If the machine is in the standby state, the switch should call the "load" file, because if the switch on the "rewind" file, electromagnetic reversing valve has been in a power-on state, affect the service life of the device.
九、控制系統保養：
Nine, control system maintenance:
1、定期檢查控制器后面板的連接線是否接觸良好，如有松動，應及時緊固;
1, regularly check the controller panel connecting line is good contact, such as loose, should be timely fastening;
2、試驗后若有一段較長的時間不用機器時，關閉控制器和電腦;
2, after the test if there is a long time not machine closed, controller and computer;
3、控制器上的接口為一一對應，插錯接口可能對設備造成損壞;
3, the controller interface for the corresponding one one, inserted the wrong interface may cause damage to the equipment;
4、插拔控制器上的接口必須關閉控制器電源。
4, Swap Controller Interface must be shut down the power supply controller.
北京北廣精儀儀器設備有限公司熱銷產品：
（橡膠塑料電性能系列）電壓擊穿試驗儀，電氣強度測試儀，介電擊穿強度測定儀，電子萬能試驗機，體積電阻率表面電阻率測試儀，介電常數及介質損耗測試儀，漏電起痕試驗儀，水平垂直燃燒儀，橡膠低溫脆性沖擊試驗儀，熔融指數儀，熔體流動速率測定儀，塑料熱變形維卡軟化點溫度測定儀，滑動摩擦磨損試驗機，耐電弧試驗機，馬丁耐熱試驗儀，建材可燃試驗儀，球壓痕硬度計，簡支梁試驗機，電熱毯動負載試驗機，萬能試驗機，沖片機，啞鈴制樣機，落錘沖擊、落鏢沖擊，落球沖擊試驗機，指數儀等
（海綿泡沫系列）海綿泡沫壓陷硬度測定儀，落球回彈試驗機，海綿切割機，海綿拉伸強度試驗機，和疲勞壓陷試驗機，壓縮變形試驗機，撕裂強度，回彈率等。
售后服務及保修承諾：
多年來，我公司一直專業生產研究電氣試驗設備，經研究、摸索、總結出一套完整的產品服務保障體系，向用戶提供優質及時的售前、售中、售后服務
為創造，提高企業度，樹立企業形象，我們本著“一切追求高質量，用戶滿意為宗旨”的精神，以“*惠的價格、zui周到的服務、zui可靠的產品質量”的原則向您鄭重承諾：
一、產品質量承諾：
1、我公司保證向需方提供的設備是原廠生產的，并且出廠資料配件齊全。為保持合同設備的正常運行和維護，我公司保證提供的技術資料和圖紙是完整、清楚和正確的。
2、產品的制造和檢測均有質量記錄和檢測資料。
3、對產品性能的檢測，我們誠請用戶親臨對產品進行全過程、全性能檢查，待產品被確認合格后再裝箱發貨。
二、產品價格承諾：
1、為了保證產品的高可靠性和先進性，系統的選材均選用國內或優質產品。
2、在同等競爭條件下，我公司在不以降低產品技術性能、更改產品部件為代價的基礎上，真誠以*惠的價格提供給貴方。
三：安裝調試及驗收承諾：
1、協助設備的安裝，負責設備的運輸、調試。
2、設備按訂貨技術附件進行驗收。終驗收在買方進行，對用戶提供的試樣進行試驗，并提供測試報告。
3、安裝調試同時，在儀器操作現場一次性免費培訓操作人員2-3名，該操作人員應是由需方選派的長期穩定的員工，培訓后能夠對設備基本原理、軟件使用、操作、維護事項理解和應用，使人員能夠獨立操作設備對樣品進行檢測、分析，同時能進行基本的維護。
四、保修承諾：
1、設備保修一年，終身服務，一年內非人為損壞的零部件免費更換，保修期內接到用戶邀請后， zui遲響應時間為2小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法 。
2、保修期內人為損壞的零部件按采購（加工）價格收費更換。
3、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后3天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。
4、傳感器過載及整機電路超壓損壞不在保修范圍內。
Beijing Beiguang precision instrument equipment Co., Ltd. - products:（series of electrical properties of rubber and plastics） voltage breakdown testing instrument, electrical strength tester, the dielectric breakdown strength tester, electronic universal testing machine, the surface resistivity tester volume resistivity, dielectric constant and dielectric loss tester, tracking test apparatus, verticalDirect combustion apparatus, rubber brittle low-temperature impact tester, melt flow index, melt flow rate detector, VEKA softening point temperature measuring instrument plastic deformation, sliding friction and wear testing machine, arc resistance test, Martin test instrument, building materials burning tester, ballIndentation hardness tester, Charpy test machine, electric blanket dynamic load testing machine, universal testing machine, punching machine, dumbbell system prototype, drop hammer impact, dart impact, falling ball impact test machine, index system（sponge foam series） sponge foam indentation hardness tester, falling ball rebound test machine, sponge cutting machine, sponge tensile strength testing machine, and the fatigue indentation test machine, compression testing machine, tear strength, rebound rate.After sale service and warranty:Over the years, our company has been specializing in the production of electrical test equipment, research, exploration, summed up a complete security system products and services, to provide quality and timely pre-sale, sale, after sale service to usersTo create a famous brand, increase brand awareness, establish a corporate image, we have the spirit of "all the pursuit of high quality, customer satisfaction as the purpose" of the spirit, to "the most preferential prices, the most attentive service, the most reliable product quality" principle solemnly promise to you:A, product quality commitment:1, our company to ensure that equipment to the need to provide the original factory, and the factory data complete accessories. In order to maintain normal operation and maintenance of contract equipment, our company guarantees to provide technical information and drawings are complete, clear and correct.2, product manufacturing and testing are quality records and test data.3, the product performance test, we ask the user to visit the whole process, the whole performance inspection of the product, the product is qualified after packing shipments.Two, the product price commitment:1, in order to ensure the high reliability and advanced products, systems material are selected domestic and international high-quality brand-name products.2, in the same competition condition, our company based on not to reduce the technical performance of products, product components for cost, provide the most preferential price to you.Three: debugging and installation acceptance commitment:1, assist the installation, transportation, commissioning of equipment.2, equipment for approval according to the order of the technical annex. Final acceptance in the buyer, for users of the test specimen, and provide the test report.3, installation and commissioning at the same time, the instrument operation on-site one-time free training 2-3, the operating personnel shall be appointed by the buyer to the long-term stability of the staff, training of basic principle, equipment, operation, maintenance issues of software comprehension and application, makePersonnel can operate independently equipment for the detection, sample analysis, and can perform basic maintenance.Four, the warranty commitment:1, equipment for one year warranty, life-long service, within one year of the non-human damage parts replaced free of charge, the warranty period the user received the invitation, the latest response time is 2 hours, and the user to confirm the fault, we will within 48 hours to send engineers to arrive at the sceneThe free service, find out the fault location and fault reason as soon as possible, and to users timely report failures and troubleshooting.2, the warranty period within the damaged parts procurement according to the price change （processing）.3, the warranty to provide quality technical services for the user, after receiving repair invited users within 3 days after the arrival of users send engineers on-site repair. And enjoy the preferential purchase fittings treatment.The 4 sensor circuit, overload and overpressure damage not covered under warranty.
- 上一個： 【斷裂強度試驗機】廠家
- 下一個： 【紙張拉力試驗機】廠家
